Department of Electronics and Communications Engineering, Vel Tech Rangarajan Dr Sagunthala R & D Institute of Science and Technology, Chennai, Tamil Nadu, India.
The current study investigates the wear behavior of three distinct composite compositions designated as C1, C2, and C3, with direct implications for aerospace applications. Critical factors such as the Coefficient of Friction (Cf), Specific Rate of Wear (Sw), and Frictional Force (FF) were meticulously analyzed using a systematic experimental approach and the Taguchi L27 array design. Significant relationships between input factors and responses emerged after subjecting these responses to Taguchi signal-to-noise ratio analysis. The optimal parameter combination of a 5% composition, 14.5 N Applied Load (Ap), 150 rpm Rotational Speed (Rs), and 40.5 m Distance of Sliding (Ds) highlights the interplay of factors in improving wear resistance. An Artificial Neural Network (ANN) was used as a predictive tool to boost research efficiency, achieving an impressive 99.663% accuracy in response predictions. The result shows comparison of the ANN's efficacy with actual experimental results. These findings hold great promise for aerospace applications where wear-resistant materials are critical for long-term performance under harsh operating conditions. The incorporation of ANN predictions allows for rapid material optimization while adhering to the stringent requirements of aerospace environments. This research contributes to the evolution of tailored composite materials, poised to improve aerospace applications with increased reliability, efficiency, and durability by advancing wear analysis methodologies and predictive technologies.
Keywords
ANN, Wear Analysis, Reinforcement, Optimisation, Prediction, Frictional Force.
D. S. E. J. Dhas, C. Velmurugan, and K. L. D. Wins, “Investigations on the Effect of Tungsten Carbide and Graphite Reinforcements during
Spark Erosion Machining of Aluminium Alloy (AA 5052) Hybrid Composite,” Silicon, vol. 10, no. 6, pp. 2769–2781, Apr. 2018, doi:
10.1007/s12633-018-9817-0.
C. Fenghong, C. Chang, W. Zhenyu, T. Muthuramalingam, and G. Anbuchezhiyan, “Effects of Silicon Carbide and Tungsten Carbide in
Aluminium Metal Matrix Composites,” Silicon, vol. 11, no. 6, pp. 2625–2632, Jan. 2019, doi: 10.1007/s12633-018-0051-6.
S. Dhanesh, K. S. Kumar, N. K. M. Fayiz, L. Yohannan, and R. Sujith, “Recent developments in hybrid aluminium metal matrix composites:
A review,” Materials Today: Proceedings, vol. 45, pp. 1376–1381, 2021, doi: 10.1016/j.matpr.2020.06.325.
Nagaraj and S. Gopalakrishnan, “A Study on Mechanical and Tribological Properties of Aluminium 1100 Alloys 6% of RHAp, BAp, CSAp,
ZnOp and Egg Shellp Composites by ANN,” Silicon, vol. 13, no. 10, pp. 3367–3376, Oct. 2020, doi: 10.1007/s12633-020-00731-8.
G. Saravanan and G. B. Bhaskar, “Influence of Silicon Carbide Reinforcements on Mechanical and Wear Behaviour AA7075/15% wt. Glass
fiber Hybrid Composites,” Silicon, vol. 15, no. 3, pp. 1451–1464, Sep. 2022, doi: 10.1007/s12633-022-02117-4.
S. Chakravarty, P. Haldar, T. Nandi, and G. Sutradhar, “Fabrication and machinability studies on cupola slag reinforced aluminium metal
matrix composites using Taguchi method,” Materials Today: Proceedings, Feb. 2023, doi: 10.1016/j.matpr.2023.02.080.
T. Banerjee, S. Dey, A. P. Sekhar, S. Datta, and D. Das, “Design of Alumina Reinforced Aluminium Alloy Composites with Improved Tribo-
Mechanical Properties: A Machine Learning Approach,” Transactions of the Indian Institute of Metals, vol. 73, no. 12, pp. 3059–3069, Oct.
2020, doi: 10.1007/s12666-020-02108-2.
P.P. Ikubanni, M. Oki, A.A. Adeleke, and O.O. Agboola, "Optimization of the tribological properties of hybrid reinforced aluminium matrix
composites using Taguchi and Grey's relational analysis," Scientific African, Vol. 12, pp. e00839, 2021, doi: 10.1016/j.sciaf.2021.e00839.
S. Pradeep Devaneyan, R. Ganesh, and T. Senthilvelan, “On the Mechanical Properties of Hybrid Aluminium 7075 Matrix Composite Material
Reinforced with SiC and TiC Produced by Powder Metallurgy Method,” Indian Journal of Materials Science, vol. 2017, pp. 1–6, Jan. 2017,
doi: 10.1155/2017/3067257.
Y. Sesharao ., “Optimization on Operation Parameters in Reinforced Metal Matrix of AA6066 Composite with HSS and Cu,” Advances in
Materials Science and Engineering, vol. 2021, pp. 1–12, Jul. 2021, doi: 10.1155/2021/1609769.
T. K. Kandavel and T. Panneerselvam, “Experimental investigations on tribological behaviour and cutting tool performance of sinter-forged
Cu, Mo and Ti added plain carbon steel,” International Journal of Machining and Machinability of Materials, vol. 18, no. 3, p. 201, 2016, doi:
10.1504/ijmmm.2016.076280.
M. Ramesh, D. Kumar, and A. Kumar, “Investigation of the effect of age hardening on the mechanical properties of aluminium metal matrix
composites reinforced with graphite particulate,” Materials Today: Proceedings, Feb. 2023, doi: 10.1016/j.matpr.2023.02.163.
T. Panneerselvam, T. K. Kandavel, and P. Kishore, “Experimental Investigation on Cutting Tool Performance of Newly Synthesized P/M
Alloy Steel Under Turning Operation,” Arabian Journal for Science and Engineering, vol. 44, no. 6, pp. 5801 –5809, Feb. 2019, doi:
10.1007/s13369-019-03763-4.
B. M. S, V. M, A. varthanan P, V. P. G, and S. P, “Multi-objective optimization of process parameters in dry sliding wear characteristics of
Al/sic composites using Taguchi grey relation analysis,” Materials Today: Proceedings, vol. 45, pp. 1882–1886, 2021, doi:
10.1016/j.matpr.2020.09.133.
S. K. Choudhary, R. S. Jadoun, and P. Singh, “Optimization of EDM process parameters for TWR on machining of Inconel 600 superalloy
using Taguchi approach,” Materials Today: Proceedings, vol. 57, pp. 2281–2288, 2022, doi: 10.1016/j.matpr.2022.01.059.
Canakci, S. Ozsahin, and T. Varol, “Prediction of Effect of Reinforcement Size and Volume Fraction on the Abrasive Wear Behavior of
AA2014/B4Cp MMCs Using Artificial Neural Network,” Arabian Journal for Science and Engineering, vol. 39, no. 8, pp. 6351–6361, May
2014, doi: 10.1007/s13369-014-1157-9.
E. N. Osegi and E. F. Jumbo, “Comparative analysis of credit card fraud detection in Simulated Annealing trained Artificial N eural Network
and Hierarchical Temporal Memory,” Machine Learning with Applications, vol. 6, p. 100080, Dec. 2021, doi: 10.1016/j.mlwa.2021.100080.
T. Varol, A. Canakci, and S. Ozsahin, “Modeling of the Prediction of Densification Behavior of Powder Metallurgy Al–Cu–Mg/B4C
Composites Using Artificial Neural Networks,” Acta Metallurgica Sinica (English Letters), vol. 28, no. 2, pp. 182–195, Dec. 2014, doi:
10.1007/s40195-014-0184-6.
Canakci, T. Varol, and S. Ozsahin, “Artificial neural network to predict the effect of heat treatment, reinforcement size, and volume fraction
on AlCuMg alloy matrix composite properties fabricated by stir casting method,” The International Journal of Advanced Manufacturing
Technology, vol. 78, no. 1–4, pp. 305–317, Dec. 2014, doi: 10.1007/s00170-014-6646-1.
R. Hesse, F. Krull, and S. Antonyuk, “Prediction of random packing density and flowability for non-spherical particles by deep convolutional
neural networks and Discrete Element Method simulations,” Powder Technology, vol. 393, pp. 559–581, Nov. 2021, doi:
10.1016/j.powtec.2021.07.056.
U. Maheshwera Reddy Paturi, H. Devarasetti, and S. Kumar Reddy Narala, “Application Of Regression And Artificial Neural Network
Analysis In Modelling Of Surface Roughness In Hard Turning Of AISI 52100 Steel,” Materials Today: Proceedings, vol. 5, no. 2, pp. 4766–
4777, 2018, doi: 10.1016/j.matpr.2017.12.050.
B. Vishnu Vardhana Naidu, M. Natarajan, G. M. Surendranatha, and K. C. Varaprasad, “Fabrication of aluminium hybrid metal mat rix
composites and development multiple regression models for wire electrical discharge machining,” International Journal on Interactive Design
and Manufacturing (IJIDeM), Jun. 2022, doi: 10.1007/s12008-022-00920-2.
H. Pulikkalparambil, A. Babu, A. Thilak, N. P. Vighnesh, S. Mavinkere Rangappa, and S. Siengchin, “A review on sliding wear properties of
sustainable biocomposites: Classifications, fabrication and discussions,” Heliyon, vol. 9, no. 3, p. e14381, Mar. 2023, doi:
10.1016/j.heliyon.2023.e14381.
M. P. Sudeshkumar, R. Ramadoss, V. Jayaseelan, and S. Vijayananth, “Preparation and Characterization of Amino-Silanized Opuntia Cladode
Fibre and Fumed Silica Toughened Epoxy Composite,” Silicon, vol. 15, no. 6, pp. 2963–2972, Nov. 2022, doi: 10.1007/s12633-022-02228-
y.
T. Gao et al., “Fiber-reinforced composites in milling and grinding: machining bottlenecks and advanced strategies,” Frontiers of Mechanical
Engineering, vol. 17, no. 2, Jun. 2022, doi: 10.1007/s11465-022-0680-8.
N. Sunitha and K. G. Manjunatha, “Evaluation of Corrosion Studies of as Casted and Heat Treated Aluminum 6065 Metal Matrix Composite
by Weight Loss Method,” Materials Today: Proceedings, vol. 5, no. 10, pp. 22727–22733, 2018, doi: 10.1016/j.matpr.2018.06.651.
Acknowledgements
The authors would like to thank to the reviewers for nice comments on the manuscript.
Funding
No funding was received to assist with the preparation of this manuscript.
Ethics declarations
Conflict of interest
The authors have no conflicts of interest to declare that are relevant to the content of this article.
Availability of data and materials
No data available for above study.
Author information
Contributions
All authors have equal contribution in the paper and all authors have read and agreed to the published version of the manuscript.
Corresponding author
Rajendra Pujari
Rajendra Pujari
Bharati Vidyapeeth (Deemed to be University), Institute of Management and Rural Development Administration, Sangli, Maharashtra, India.
Open Access This article is licensed under a Creative Commons Attribution NoDerivs is a more restrictive license. It allows you to redistribute the material commercially or non-commercially but the user cannot make any changes whatsoever to the original, i.e. no derivatives of the original work. To view a copy of this license, visit https://creativecommons.org/licenses/by-nc-nd/4.0/
Cite this article
Rajendra Pujari, Mageswari M, Herald Anantha Rufus N, Prabagaran S, Mahendran G and Saravanan R, “Artificial Neural Network Based Wear and Tribological Analysis of Al 7010 Alloy Reinforced with Nanoparticles of SIC for Aerospace Application”, Journal of Machine and Computing, vol.3, no.4, pp. 446-455, October 2023. doi: 10.53759/7669/jmc202303036.
